#CADDX DL900 DOWNLOAD HOW TO#
#CADDX DL900 DOWNLOAD SERIAL#
#CADDX DL900 DOWNLOAD MANUAL#
#CADDX DL900 DOWNLOAD SOFTWARE#

If the panel is unlocked, NX Unlocker will tell you. Wait a few seconds and read the results.Ĩ. Select the com port the NX-586E is attached toħ.

#CADDX DL900 DOWNLOAD SOFTWARE#

Consult the DL900 software for help setting up your software.ĥ. If you do not receive this error, your DL900 software is not configured properly for direct access. You will receive the following error “Incorrect control access code!” Attempt a direct connect with the panel using DL900 with any access code.

*steps 2 and 3 are optional but necessary to ensure that your computer is able to communicate with the panel and the panel responds properly*Ģ.

#CADDX DL900 DOWNLOAD SERIAL#

Attach the NX-586E to a free com port on your computer (or to a USB Serial Adapter) and the panel to unlock following the directions that came with the NX-586E. ↳ Touchpanels, Displays & UMPC devices.1.↳ Philips Pronto (TSU9600), IRtrans and other remotes.↳ Rfxcom Receivers & Transmitters Forum.↳ Kickstarter, Indiegogo and other crowdfunding related smartthings.Hopefully this will help others in the future. > Then pushed the config back to the module, and all worked fine. The code that was read by the panel then gets chopped in to facility number and badge number as it should be with Wiegand format (this might not be necessary in all cases, some of my badges got discovered correctly as format 1 after reading) > I had to change the Wiegand protocol value from '255' (default value) to '1' because I use Wiegand format 1. It should show your badges attached to the userIDs. Fetch your configuration after scanning, select Expanders > Door Control > Badge numbers (on the bottom of the menu list). The reader will flash green according to the manual.Ĥ) I used the DL900 software to see if it learnt the badges ok. Download If your download is not starting, click here. Compatible with Microsoft Windows 7 and 8, this is available to download from our website (to be completed).

#CADDX DL900 DOWNLOAD MANUAL#

This could be a firmware difference.Ģ) If you use 6 digit codes, you need to pre-fill the userID with zero's (add 2): 'b00001' for user 1 when using 6-digit, 'b001' for 4-digit.ģ) After the code is entered, the panel accepts a card (without any notice on the keypad!) while the display asks for the new userID. ZeroWire Installation Manual 45 DLX900 Software DLX900 is a fully featured management tool for control rooms and security professionals. There are several issues adding to the confusion:ġ) When selecting 'Stay' or one or the other functions to start the card programming (Step 3), the display normally shows a 'b', in my case it where just '*'.

#CADDX DL900 DOWNLOAD HOW TO#

Does anybody know how to program the cards, and what should happen when pressing, or ? It seems the system does not change in 'card' programming mode when changing to user 002. *003**)ĭouble checked if the reader is setup to do card programming (Loc.3, Seg.1, Option1). Entering a user number only results in entering a partial new code for user 002 (i.e. Scanning a card or entering a user number does not change anything. First digit of the user code turns in a star it does not ask for a new user number, reader and keypad do not change status in any way Looking at the manual, it is the same as with the NX-1700 modules.Ġ02 It then shows the current code for user 2 The trouble starts when trying to enter the user programming mode. The reader also beeps when I hold a card close to it, so it does read. So far it seems the expansion board is recognized (seen in DL900), board and reader settings have been applied. Unfortunately I cannot get any cards recognized by the system. I've installed the NX-1710E expansion board in my NX-8E with a Wiegand cardreader. As most people start programming their alarm's basic setup before starting on the extra's such as the doorcontroller, this normally shouldn't be an issue. So to keep this information available to the world I'll repost it here.īe aware, basic Networx programming experience is needed to understand this walkthrough. I've figured this out a few years ago and shared this knowledge on a US based forum which is now closed for people outside the US. For those who work with a Networx or Caddx security panel in combination with a NX-1710E doorcontroller with a Wiegand cardreader, here is some extra information on programming.

Caddx dl900 download